They are making several good annotation about A Step-by-Step Guide to Installing a Bathtub in general in this post following next.
Installing a bathtub isn't precisely brain surgery, but it does call for solid plumbing, carpentry, and also often, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably difficult job. If the old tub is readily accessible, the task can relocate easily; if you have to open a wall surface to get rid of the old bathtub and also place the brand-new tub, the task is a lot harder. In either instance, the task is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and also set in the new one. See to it you have qualified yourself for the work as well as fit attempting it. Rather than working with a specialist to take over a halfway-completed task, it is much better to consider utilizing one before you begin. Chances are you may require a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your shower room if you have actually already gotten a brand-new tub and also don't need to alter the setup of your previous water supply pipes.
Your tools as well as product list should make up the following:
Preparing for the Setup
To start with, the sustaining framework supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop stress on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you use every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you should do is detach the water system. After doing so, switch on the taps to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be quite bothersome due to the limited accessibility that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipelines. Once the supply pipes have been gotten rid of, use the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from turning during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Setting up the Tub
Utilizing both wooden boards under its feet, place the bath tub in the needed setting. The wood boards are handy in uniformly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to make certain that the tub is leveled all round. This can be achieved by checking the level and adjusting the feet on the bath tub up until the level reads degree.
To mount taps, fit the bottom of the furthest adaptable faucet adapter to the proper supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water and also inspect all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill the bathtub as well as also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bath tub must wait up until the tub has been made use of at the very least when as this will resolve it right into its final setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making certain that the washing machines are in place between the faucet and also the sink. Safeguard the tap in place with the maker offered backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The previous type must be linked to the tap ends initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to crack an inflexible seal, causing the water to pass through the wall surface in between the bathroom and the tiling, bring about problems with wetness as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and also fittings. They are marketed in tubes and also cartridges, as well as are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of drenched newspaper or soft rope. Remember to always load the tub with water before sealing, to permit the movement experienced when the bathtub is in usage. The sealer can break rather early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally quickly readily available on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic reader about A Step-by-Step Guide to Installing a Bathtub, I figured sharing that excerpt was a great idea. Enjoyed our posting? Please share it. Help other people check it out. Thanks so much for taking the time to read it.
Trust our expertise.
Judge Reinhold Then & Now!
Keshia Knight Pulliam Then & Now!
Elisabeth Shue Then & Now!
Shannon Elizabeth Then & Now!
Nicki Minaj Then & Now!